__ __ __ __ _____ _ _ _____ _ _ _
| \/ | \ \ / / | __ \ (_) | | / ____| | | | |
| \ / |_ __\ V / | |__) | __ ___ ____ _| |_ ___ | (___ | |__ ___| | |
| |\/| | '__|> < | ___/ '__| \ \ / / _` | __/ _ \ \___ \| '_ \ / _ \ | |
| | | | |_ / . \ | | | | | |\ V / (_| | || __/ ____) | | | | __/ | |
|_| |_|_(_)_/ \_\ |_| |_| |_| \_/ \__,_|\__\___| |_____/|_| |_|\___V 2.1
if you need WebShell for Seo everyday contact me on Telegram
Telegram Address : @jackleet
For_More_Tools:
# SPDX-License-Identifier: GPL-2.0
if NLM_XLP_BOARD || NLM_XLR_BOARD
if NLM_XLP_BOARD
config DT_XLP_EVP
bool "Built-in device tree for XLP EVP boards"
default y
select BUILTIN_DTB
help
Add an FDT blob for XLP EVP boards into the kernel.
This DTB will be used if the firmware does not pass in a DTB
pointer to the kernel. The corresponding DTS file is at
arch/mips/netlogic/dts/xlp_evp.dts
config DT_XLP_SVP
bool "Built-in device tree for XLP SVP boards"
default y
select BUILTIN_DTB
help
Add an FDT blob for XLP VP boards into the kernel.
This DTB will be used if the firmware does not pass in a DTB
pointer to the kernel. The corresponding DTS file is at
arch/mips/netlogic/dts/xlp_svp.dts
config DT_XLP_FVP
bool "Built-in device tree for XLP FVP boards"
default y
select BUILTIN_DTB
help
Add an FDT blob for XLP FVP board into the kernel.
This DTB will be used if the firmware does not pass in a DTB
pointer to the kernel. The corresponding DTS file is at
arch/mips/netlogic/dts/xlp_fvp.dts
config DT_XLP_GVP
bool "Built-in device tree for XLP GVP boards"
default y
select BUILTIN_DTB
help
Add an FDT blob for XLP GVP board into the kernel.
This DTB will be used if the firmware does not pass in a DTB
pointer to the kernel. The corresponding DTS file is at
arch/mips/netlogic/dts/xlp_gvp.dts
config DT_XLP_RVP
bool "Built-in device tree for XLP RVP boards"
default y
help
Add an FDT blob for XLP RVP board into the kernel.
This DTB will be used if the firmware does not pass in a DTB
pointer to the kernel. The corresponding DTS file is at
arch/mips/netlogic/dts/xlp_rvp.dts
config NLM_MULTINODE
bool "Support for multi-chip boards"
depends on NLM_XLP_BOARD
default n
help
Add support for boards with 2 or 4 XLPs connected over ICI.
if NLM_MULTINODE
choice
prompt "Number of XLPs on the board"
default NLM_MULTINODE_2
help
In the multi-node case, specify the number of SoCs on the board.
config NLM_MULTINODE_2
bool "Dual-XLP board"
help
Support boards with upto two XLPs connected over ICI.
config NLM_MULTINODE_4
bool "Quad-XLP board"
help
Support boards with upto four XLPs connected over ICI.
endchoice
endif
endif
config NLM_COMMON
bool
endif